NAVIGATE

Table of Contents

STATISTICS

Viewed3282

Downloads2022

Research on the Influence of Interference Fit Parameters of Shaft and Gear on Tooth Profile
[HTML]   PDF下载 (2022)
[1]ZHOU Yang,XU Gaijiao,LI Dalei.Research on the Influence of Interference Fit Parameters of Shaft and Gear on Tooth Profile[J].Journal of Zhengzhou University (Engineering Science),2020,41(03):57-61.[doi:10.13705/j.issn.1671-6833.2019.02.018]
Copy
Journal of Zhengzhou University (Engineering Science)[ISSN 1671-6833/CN 41-1339/T] Volume: 41卷 Number of periods: 2020 03 Page number: 57-61 Column: Public date: 2020-07-29
Title:
Research on the Influence of Interference Fit Parameters of Shaft and Gear on Tooth Profile
Author(s):
ZHOU Yang;  XU Gaijiao;  LI Dalei
School of Mechanical and Power Engineering, Zhengzhou University, Zhengzhou 450001,China
Keywords:
interference fit;  Lame equation;  friction coefficient; interference;  radial displacement
CLC:
-
DOI:
10.13705/j.issn.1671-6833.2019.02.018
Abstract:
In order to study the influence of shaft-gear interference fit on tooth profile, the calculation model of the tooth deformation was proposed by combining the shaft-gear interference which based on Lame equation and involute equation was established by finite element method in this paper. At the same time, the corresponding calculation program was compiled based on MATLAB, and the influence of the friction coefficient, interference and other parameters on the radial displacement of the gear tooth shape was studied. The results showed that the radial deformation of the gear increased with the increase of the friction coefficient and interference, and decreased with the increase of the number of teeth.
References:
[1] 刘竹丽,赵敏敏,马朋朋,等.基于ANSYS的斜齿轮副接触分析与可靠性分析[J]. 郑州大学学报(工学版),2015,36(2):6-9.
[2] 李亚洲,汤易升,陈炜,等.基于ANSYS Workbench对圆柱面过盈配合接触应力的研究[J]. 天津理工大学学报,2017, 33(3):1-5.
[3] 濮良贵.机械设计[M]. 8版.北京：高等教育出版社，2005：129-136.
[4] JIN X, ZHANG Z J, YE X, et al. Calculating model of interference amount for miniaturized gear and shaft shrinkFit[J]. Journal of Beijing institute of technology, 2006, 15(2):138-143.
[5] ZHANG Y, MCCLAIN B, FANG X D,et al. Design of interference fits via finite element method[J]. International journal of mechanical sciences, 2000, 42(9):1835-1850.
[6] SEN S, AKSAKAL B. Stress analysis of interference fitted shaft-hub system under transient heat transfer conditions[J]. Materials & design, 2004, 25(5):407-417.
[7] 邹渊,孙逢春,王文清, 等. 过盈配合时齿轮内径与预应力关系研究[J]. 机械传动, 2003，27(6):45-46,55.
[8] 王少江,李学明,张安鹏, 等. 大型焊接齿轮与轴过盈配合有限元分析[J]. 煤矿机械, 2015，36(5):140-142.
[9] 关丽坤,任学平,郭书萍，等.过盈联接的有限元分析[J]. 机械设计, 2005, 22(增刊1):275-276.
[10] CHU S J, JEONG T K, JUNG E H,et al. Effect of radial interference on torque capacity of press- and shrink-fit gears[J]. International journal of automotive technology, 2016, 17(5):763-768.
[11] 何亚峰,杨小斌,干为民，等.齿轮与轴压装过程过盈配合研究[J]. 机械传动,2014,38(12):33-36.
[12] 张炳义,戴思锐,冯桂宏，等.磁力齿轮内转子护套过盈量计算及其应力分析[J]. 机电工程, 2017, 34(8):817-822.
[13] 贾国海,龚金科,鄂加强,等.齿轮轴过盈配合对轴肩微动磨损的影响研究[J]. 湖南大学学报(自然科学版),2013，40(5):36-41.
[14] 赵俊,林腾蛟,钟声,等.行星轮-轴承过盈配合部位疲劳寿命及其影响因素分析[J]. 大连理工大学学报, 2016, 56(4):355-361.
[15] LANOUE F, VADEAN A, SANSCHAGRIN B, et al. Finite element analysis and contact modelling considerations of interference fits for fretting fatigue strength calculations[J]. Simulation modelling practice & theory, 2009, 17(10):1587-1620.
Similar References:
Memo

-

Last Update: 2020-07-29
Copyright © 2023 Editorial Board of Journal of Zhengzhou University (Engineering Science)