[1]卢红霞,高凯,李明亮,等.以高炉渣为助烧剂制备ZTA/TiC复合陶瓷及其性能研究[J].郑州大学学报(工学版),2020,41(05):8-14.
　LU Hongxia,GAO Kai,LI Mingliang,et al.Preparation of ZTA/TiC Composite Ceramics Using Blast Furnace Slag as Sintering Aid[J].Journal of Zhengzhou University (Engineering Science),2020,41(05):8-14.
点击复制

以高炉渣为助烧剂制备ZTA/TiC复合陶瓷及其性能研究()
分享到：

《郑州大学学报(工学版)》[ISSN:1671-6833/CN:41-1339/T]

卷:
41
期数:
2020年05期
页码:
8-14
栏目:
出版日期:
2020-10-01

文章信息/Info

Title:
Preparation of ZTA/TiC Composite Ceramics Using Blast Furnace Slag as Sintering Aid
作者:
卢红霞; 高凯; 李明亮; 王海龙
Author(s):
LU Hongxia1; 2;  GAO Kai2;  LI Mingliang1;  WANG Hailong1; 2
1.School of Materials Science and Engineering, Zhengzhou University, Zhengzhou 450001, China; 2.Henan Province Industrial Technology Research Institute of Resources and Materials, Zhengzhou University, Zhengzhou 450001, China
Keywords:
ZTA/TiC composite ceramics;  blast furnace slag;  crystallization;  low temperature sintering;  mechanical properties
文献标志码:
A
摘要:
以3μm α -Al 2 0 3 为主要原料,辅以纳米Al 2 0 3 、ZrO 2 ,和TiC等原料,工业废渣一高炉渣为助烧剂,热压烧结制备ZTA/TiC复合陶瓷。利用XRF、XRD、DSC、SEM、三点弯曲试验和维氏压痕等表征手段,研究了原料组成和烧结温度对复合陶瓷物相组成、微观结构及力学性能的影响。结果表明:15%(质量分数,下同)纳米Al 2 0 3 及5%纳米TiC的加入有利于复合陶瓷力学性能的提升,烧结温度为1650 ℃ 时,材料的抗弯强度和断裂韧性分别为510MPa和6.58MPa.m 1/2 ,沿晶断裂与穿晶断裂同时存在,使复合陶瓷有较好的综合性能。添加质量分数为4%的高炉渣，1550 ℃ 热压烧结30min,得到的ZTA/TiC复合陶瓷相对密度为99.5%,抗弯强度和断裂韧性分别为555MPa和5.20MPa.m 1/2 ",比相同温度下未添加高炉渣时的性能优良。烧结时高炉渣产生的液相可促进Al 2 0 3 棒晶生长并降低烧结温度;同时由于其析晶特性,陶瓷基体中的玻璃相减少,陶瓷强度提高。
Abstract:
ZTA/TiC composite ceramics were prepared by using 3 μm α-Al2O3 particles as main raw material, supplemented by nano-materials such as Al2O3, ZrO2 and TiC, and industrial waste residue (blast furnace slag) used as sintering aid. The effects of raw material composition and sintering temperature on the phase composition, microstructure and mechanical properties of the materials were studied by X-ray fluorescence spectrometry (XRF), X-ray diffraction (XRD), differential scanning calorimetry (DSC), scanning electron microscope (SEM), three-point bending test and Vickers indentation, respectively. The results showed that addition of 15% nano-Al2O3 and 5% nano-TiC was beneficial to the improvement of the mechanical properties of the composite ceramics. Flexural strength and fracture toughness of such composites sintered at 1 650 ℃ reached 510 MPa and 6.58 MPa·m 1/2, respectively. Existence of intergranular fracture and transgranular fracture led to composite ceramics possessing better comprehensive properties. When the content of blast furnace slag was 4%, the relative density of samples sintered at 1 550 ℃ for 30 min reached 99.5%, and flexural strength and fracture toughness were 555 MPa and 5.20 MPa·m1/2, respectively. Liquid phase produced by blast furnace slag in the sintering process promoted growth of Al2O3 rods and decreased sintering temperature. Furthermore, content of glass phase in the ceramic matrix decreased and ceramic strength increased due to crystallization characteristics of blast furnace slag.

参考文献/References:

[1] GUIMARAES F A T, SILVA K L, TROMBINI V, et al. Correlation between microstructure and mechanical properties of Al2O3/ZrO2 nanocomposites[J]. Ceramics international, 2009, 35(2): 741-745.

[2] 黄传真, 孙静, 孙高祚,等. ZrO2/Al2O3 陶瓷刀具材料的增韧补强机理分析[J]. 机械工程师, 2003(8): 3-6.
[3] 安然, 肖建中, 夏风. TiO2含量对 ZTA 陶瓷性能的影响[J]. 硅酸盐通报, 2011, 30(1): 191-194.
[4] 薛伟江, 谢志鹏. 低温环境下结构陶瓷的相变、断裂机理与性能的研究进展[J]. 无机材料学报, 2014, 29(4): 337-344.
[5] ECHEBERRIA J, OLLO J, BOCANEGRA-BERNAL M H, et al. Sinter and hot isostatic pressing (HIP) of multi-wall carbon nanotubes (MWCNTs) reinforced ZTA nanocomposite: microstructure and fracture toughness[J]. International journal of refractory metals and hard materials, 2010, 28(3): 399-406.
[6] 赵世柯, 黄校先, 施鹰,等. 改善氧化锆陶瓷材料抗热震性的探讨[J]. 陶瓷学报, 2000, 21(1): 41-45.
[7] 赵威, 王红兵, 陈鹏程, 等. 喷雾造粒制备ZTA复合粉体及其烧结体性能的研究[J]. 稀有金属材料与工程, 2015, 44(增刊1): 749-752.
[8] 钟金豹, 黄传真, 聂乾利. 纳米碳化钛颗粒对纳米氧化锆增韧氧化铝基陶瓷刀具材料的影响[J]. 工具技术, 2011,45(12): 27-30.
[9] ZHU T B, XIE Z P, HAN Y, et al. Microstructure and mechanical properties of ZTA composites fabricated by oscillatory pressure sintering[J]. Ceramics international, 2018, 44(1): 505-510.
[10] NAGA S M, HASSAN A M, AWAAD M, Physical and mechanical properties of Ta2O5 doped zirconia-toughened alumina (ZTA) composites[J]. Ceramics international, 2015, 41(5): 6248-6255.
[11] CHAE J, CHO B. Effect of SiO2, CaCO3 and talc on sintering behavior of ZTA [J]. Journal of ceramic processing research, 2013, 14(2): 210-212.
[12] MA D C, CHEN H T, CHENG X Q, et al. Preparation and properties of ZTA ceramics using blast furnace slag as sintering additives[J]. Materials research express, 2019, 6(6): 065201.
[13] FRANCIS A A, ABDEL RAHMAN M K, DAOUD A. Processing, structures and compressive properties of porous glass-ceramic composites prepared from secondary by-product materials [J]. Ceramics international, 2013, 39(6): 7089-7095.
[14] 卢红霞, 吕泽刚, 程向前,等. 利用废渣一次烧结制备微晶玻璃釉面砖的研究[J]. 郑州大学学报(工学版), 2018, 39(2): 92-96.

更新日期/Last Update: 2020-10-23