[1]刘春红,李成贵,张庆荣,等.微晶玻璃研磨抛光超光滑表面粗糙度的工艺研究[J].郑州大学学报(工学版),2007,28(04):126-128.[doi:10.3969/j.issn.1671-6833.2007.04.031]
　LIU Chunhong,Li Chenggui,ZHANG Qingrong,et al.Research on the process of grinding and polishing ultra-smooth surface roughness of glass-ceramic[J].Journal of Zhengzhou University (Engineering Science),2007,28(04):126-128.[doi:10.3969/j.issn.1671-6833.2007.04.031]
点击复制

微晶玻璃研磨抛光超光滑表面粗糙度的工艺研究()
分享到：

《郑州大学学报(工学版)》[ISSN:1671-6833/CN:41-1339/T]

卷:
28卷
期数:
2007年04期
页码:
126-128
栏目:
出版日期:
1900-01-01

文章信息/Info

Title:
Research on the process of grinding and polishing ultra-smooth surface roughness of glass-ceramic
作者:
刘春红; 李成贵; 张庆荣; 等.
北京航空航天大学,仪器科学与光电工程学院,北京,100083, 北京航空航天大学,仪器科学与光电工程学院,北京,100083, 北京航空航天大学,仪器科学与光电工程学院,北京,100083, 北京航空航天大学,仪器科学与光电工程学院,北京,100083
Author(s):
LIU Chunhong; Li Chenggui; ZHANG Qingrong; etc
关键词:
微晶玻璃;  研磨抛光;  粗糙度;  工艺
Keywords:
DOI:
10.3969/j.issn.1671-6833.2007.04.031
文献标志码:
A
摘要:
研磨抛光采用浸液式定偏心锡磨盘抛光方式,研究抛光液浓度、PH值、上下研磨盘转速、抛光时间等参数对微晶玻璃超光滑表面粗糙度的影响,粗糙度的测量采用NT1100干涉仪.实验结果表明:粗糙度受PH值影响比较大;试件在低浓度弱碱抛光液中,延长抛光时间可降低表面粗糙度值并获得高质量的表面,最终测得表面粗糙度为Ra=0.37 nm.
Abstract:
The polishing method of immersion fixed eccentric tin grinding disc was adopted to study the influence of polishing liquid concentration, PH value, upper and lower grinding disc speed, polishing time and other parameters on the ultra-smooth surface roughness of glass-ceramic, and NT1100 interferometer was used for roughness measurement. The experimental results show that the roughness is greatly affected by the PH value. In the low concentration of weak alkali polishing solution, extending the polishing time can reduce the surface roughness value and obtain a high-quality surface, and the final measured surface roughness is Ra=0.37 nm.

相似文献/References:

[1]卢红霞,吕泽刚,程向前,等.利用废渣一次烧结制备微晶玻璃釉面砖的研究[J].郑州大学学报(工学版),2018,39(02):92.[doi:0.13705/j.issn.1671-6833.2017.05.014]
　Lu Hongxia,Lu Zegang,Cheng Qianqian,et al.Study on Glazed Tile of Glass-ceramic from Waste Residue Prepared by Direct Sintering Process[J].Journal of Zhengzhou University (Engineering Science),2018,39(04):92.[doi:0.13705/j.issn.1671-6833.2017.05.014]

更新日期/Last Update: 1900-01-01