[1]孙振起,黄明辉,刘昌发..航空用钛合金表面处理工艺参数优化[J].郑州大学学报(工学版),2012,33(02):125-128.[doi:10.3969/j.issn.1671-6833.2012.02.030]
　SUN Zhenqi,HUANG Minghui,LIU Changfa.Optimization of Titanium Alloy Surface Anodic Treatment Parameters[J].Journal of Zhengzhou University (Engineering Science),2012,33(02):125-128.[doi:10.3969/j.issn.1671-6833.2012.02.030]
点击复制

航空用钛合金表面处理工艺参数优化()
分享到：

《郑州大学学报(工学版)》[ISSN:1671-6833/CN:41-1339/T]

卷:
33卷
期数:
2012年02期
页码:
125-128
栏目:
出版日期:
2012-03-10

文章信息/Info

Title:
Optimization of Titanium Alloy Surface Anodic Treatment Parameters
作者:
孙振起; 黄明辉; 刘昌发.
中南大学机电学院,湖南长沙,410083, 中南大学机电学院,湖南长沙,410083, 中南大学机电学院,湖南长沙,410083
Author(s):
SUN Zhenqi; HUANG Minghui; LIU Changfa
School of Mechanical and Electrica! Engineering, Central South University, Changsha 410083, China
关键词:
钛合金;  阳极化表面处理;  正交实验法;  工艺参数优化
Keywords:
titanium alloy ;  anodization surface treatment;  orthogonal experiment;  process parameters optimiation
分类号:
V261.3
DOI:
10.3969/j.issn.1671-6833.2012.02.030
摘要:
摘要:采用正交试验法对航空业最常用的钛合金Ti-6Al-4V表面阳极处理工艺参数优化进行了研究,得出的最佳工艺参数为:溶液浓度250 g/L,处理时间15 min,直流电压10 V,温度25℃.通过阳极化处理,在钛合金表面形成了一层褐色、致密、多孔的氧化层,增加了合金表面积,促进了胶接表面与胶层的机械咬合,增强了胶接强度.力学实验证明,胶接试样的剪切强度可达34.54 MPa.
Abstract:
Ti-6Al-4V is an important alloy in aviation field. In this paper, orthogonal experiment method wasused to optimize the parameters of surface treatment, which affect the results of the anodization. The best pa*rameters were obtained with this method: 250 g/L of solution concentration, 10 V electric voltage and 15 mi.nutes anodization time, 25 9 experimental temperature. Brown, tight and porous oxide layer was developedon the surface of titanium alloy. This oxide layer increased the surface of the sampld, and enlarged the in.termeshing strength between the cohesive and sample during bonding. Mechanical test results showed that thecohesive joint shear strength comes up to 34.54 MPa according to this optimized program.

相似文献/References:

[1]隋艳伟,刘爱辉,李邦盛,等.钛合金离心铸造缩孔缺陷物理模拟研究[J].郑州大学学报(工学版),2009,30(01):61.
　SUI Yanwei,LIU Aihui,LI Bangsheng,et al.Physical Simulation Study on Shrinkage Defects of Titanium Alloy Centrifugal Casting[J].Journal of Zhengzhou University (Engineering Science),2009,30(02):61.

更新日期/Last Update: 1900-01-01