[1]许德刚,翟萍,秦力一..汽轮机的转子损伤与优化启动[J].郑州大学学报(工学版),2002,23(04):1-3.[doi:10.3969/j.issn.1671-6833.2002.04.001]
 Xu Degang,Zhai Ping,Qin Liyi.Rotor damage and optimized start of steam turbines[J].Journal of Zhengzhou University (Engineering Science),2002,23(04):1-3.[doi:10.3969/j.issn.1671-6833.2002.04.001]
点击复制

汽轮机的转子损伤与优化启动()
分享到:

《郑州大学学报(工学版)》[ISSN:1671-6833/CN:41-1339/T]

卷:
23
期数:
2002年04期
页码:
1-3
栏目:
出版日期:
1900-01-01

文章信息/Info

Title:
Rotor damage and optimized start of steam turbines
作者:
许德刚翟萍秦力一.
郑州大学工程力学系,河南,郑州,450002, 郑州大学工程力学系,河南,郑州,450002, 郑州大学工程力学系,河南,郑州,450002
Author(s):
Xu Degang; Zhai Ping; Qin Liyi
关键词:
汽轮机 转子 损伤 优化启动
Keywords:
DOI:
10.3969/j.issn.1671-6833.2002.04.001
文献标志码:
A
摘要:
针对汽轮机启动时机器损耗和燃料损耗都很大且容易出事故这一问题,研究了转子的热应力计算,导出了转子热应力计算公式;根据连续损伤理论,讨论了转子的疲劳损伤计算,并从总损耗最小出发,探讨了汽轮机的优化启动问题.研究结果表明,汽轮机启动时的热应力并非越低越好,而是存在一最佳值,在此值附近启动效益最好.
Abstract:
Aiming at the problem that the machine loss and fuel loss are large and prone to accidents when the steam turbine is started, the calculation of the thermal stress of the rotor is studied, and the calculation formula of the rotor thermal stress is derived. According to the continuous damage theory, the fatigue damage calculation of the rotor is discussed, and the optimization and starting problem of the steam turbine is discussed from the minimum total loss. The results show that the thermal stress at the start-up of the turbine is not as low as possible, but there is an optimal value, and the starting benefit is best around this value.

相似文献/References:

[1]周俊杰,王璞,周金方.基于ANSYS CFX的汽轮机叶片气动性能优化模拟研究[J].郑州大学学报(工学版),2017,38(04):1.[doi:10.13705/j.issn.1671-6833.2017.01.008]
 Zhou Junjie,Wang Pu,Zhou Jinfang.Study on Numerical Simulation of The Steam Turbine Blade Aerodynamic steam turbine increases.Performance Optimization Based on ANSYS CFX[J].Journal of Zhengzhou University (Engineering Science),2017,38(04):1.[doi:10.13705/j.issn.1671-6833.2017.01.008]
[2]周俊杰,王梅玲,郭朋飞,等.汽轮机叶型的三维数值模拟及优化[J].郑州大学学报(工学版),2015,36(01):49.[doi:10.3969/ j. issn.1671 -6833.2015.01. 012]
 ZHOU Jun-jie,WANG Mei-ling,GUO Peng-fei,et al.Three-dimensional Numerical Simulation and Optimization of Steam Turbine Blade[J].Journal of Zhengzhou University (Engineering Science),2015,36(04):49.[doi:10.3969/ j. issn.1671 -6833.2015.01. 012]
[3]王定标,雷风林,向飒,等.汽轮机末级变工况三维数值模拟与叶型改进设计[J].郑州大学学报(工学版),2010,31(05):1.[doi:10.3969/j.issn.1671-6833.2010.05.001]
[4]张永宇,杨飞龙,周万春,等.罗茨鼓风机转子渐开线型线设计与加工[J].郑州大学学报(工学版),1999,20(03):87.[doi:10.3969/j.issn.1671-6833.1999.03.030]

更新日期/Last Update: 1900-01-01